How To Get One End Of A Stuck Drawstring Pulled Back Out Of A Hoodie?
By Appliance Repair Assistant
/ May 11, 2016
I pulled the drawstring on my hoodie half way out. One end of the string is there and the other end of the drawstring is stuck somewhere in the middle. How do I feed the drawstring back out of the hole? Can I do it without removing the complete string? If I pull it out all the way, I do not think I can ever get it back in again. I tried the paper clip and safety pin trick but it did not work. Is there an easy way to do this fast?
Use a Coat Hanger: (use this method if you need to get the complete drawstring back into a hoodie)
- Put a small hook on the end of a metal coat hanger with pliers.
- Slide it into the hoodie drawstring channel.
- Slide it until it is about an inch past the end of the drawstring.
- Rotate the coat hanger a full circle to try and “grab” the drawstring.
- Carefully slide the coat hanger out and the end of the drawstring should be attached.
- (Once both ends of the drawstring are out, tie a small tight knot on each end so this does not happen again)
Use Needle Nose Pliers:
- Bunch up the hoodie drawstring channel.
- Bunch it up until you are as close to the end of the drawstring as possible.
- Slide the end of your needle nose pliers into the channel.
- Grab the end of the drawstring with the pliers and pull out.
- (Once both ends of the drawstring are out, tie a small tight knot on each end so this does not happen again)
Use a Knitting Needle:
- Put it in the hole that the drawstring is stuck in and follow up to the end of the string.
- Be sure to bunch up the fabric as you go.
- You will have to spear the end of the drawstring and then carefully pull it out.
- (Once both ends of the drawstring are out, tie a small tight knot on each end so this does not happen again)
Drawstring Replacement
Use a Safety Pin:
- Slide a safety pin through the end of the channel where the drawstring in stuck.
- Feel through the material and grip the pin flat.
- Hold the pin on the string end.
- Slide the string channel material over the pin and grab the outboard end of the pin.
- Draw the hoodie material backwards over the string.
- Keep doing this until you have the string out the other end.
- (Once both ends of the drawstring are out, tie a small tight knot on each end so this does not happen again)
Use a Paper Clip:
- Put a small hook on the end of a paper clip using needle nose pliers.
- Slide it into the hoodie drawstring channel while “bunching up the material”.
- Slide the paper clip until it is about an inch past the end of the drawstring.
- Rotate the paper clip a few times to try and “grab” the drawstring.
- Carefully slide the paper clip out and the end of the drawstring should be attached.
- (Once both ends of the drawstring are out, tie a small tight knot on each end so this does not happen again)
Use a Drinking Straw:
- Slide the straw into the channel.
- Work the straw into the hoodie channel until you reach the end of the drawstring.
- Slide the straw onto the end of the drawstring.
- With the string stuck in the straw, slide the straw out and the drawstring should come with it.
- (Once both ends of the drawstring are out, tie a small tight knot on each end so this does not happen again)
Use the Easy Threader Flexible Needle Drawstring replacement tool
NOTE: These methods work for ANYTHING that has a drawstring including men’s swim shorts and sweatpants.
These methods will also work for getting a completely removed drawstring back into a hoodie, sweatpants, or swim shorts.
How to restring your Hoodie or Sweatshirt in less than a Minute!
Please Share Our Repair Help
6 Easy Ways to Recover A Hoodie String
There comes a time when we pull hoodie strings halfway out. We see one end of the string there; the other we don’t. Now, fret not. Because there are a lot of ways by which you can recover the other half. You can use a coat hanger or needle-nose pliers. Using a knitting needle or a safety pin also works. The same is true with a paperclip and a lot more.
Recovering a hoodie string should never be a problem at all.
When you see one end of the string and the other you cannot, the string is somewhere in the middle.
Now, how do you recover the other half? Can you do it without resorting to removing the whole string out of the hoodie?
The risk there is that if you pull it all the way out, can you put it back in?
When in such a situation, fret not.
There are many ways by which you can fix this. Not only are your options many, but they’re also pretty easy.
Read on to find out.
Using a Coat Hanger
This part here is something that you can use to draw the whole string out of the hoodie.
Start by putting a small hook on one end of the metal coat hanger. You can use pliers to do this.
Slide the hooked hanger into the hoodie drawstring channel. This is the hole where the string comes in and out. Next, you slide the hooked hanger in. Slide it until it goes about an inch past the end of the drawstring.
Then you rotate the coat hanger. Make sure that you rotate the hanger a full circle. This is for the hanger to try and grab the drawstring.
Once done, you slide the coat hanger out. This is when you ensure that the end of the drawstring is already attached.
Once this is finally done, make sure that this does not happen again. To do that, tie a small knot on each end of the drawstring. The knot should be tight. And for you not to go through this again, the knot should be bigger than the hole of the drawstring channel.
Using Needle Nose Pliers
This is one of the most common ways to fix the problem.
You start by bunching up the hoodie channel. This, as discussed, is the pathway through which the drawstring goes through.
When doing this, make sure that you bunch the channel up until you feel the end of the drawstring. It may sometimes be in the middle of the channel or towards the end. No matter where it is, do not stop bunching the channel until you feel the end of the drawstring.
Next is to slide the end of the needle nose pliers inside the drawstring channel. This should be something that you use to grab the end of the drawstring. Once you can grab the end of the drawstring, slowly pull it out.
As always, once fixed, make sure to tie a knot on each end of the drawstring. This should prevent you from going through this ordeal over again.
Using a Knitting Needle
In this method, one needs to be careful to avoid pricking.
Start by putting the knitting needle inside the drawstring channel. Bunch up the fabric until you reach the end of the string that you want to pull out.
The next thing to do is to spear the end of the drawstring. Once you can do this, slowly pull the drawstring out.
Once out, tie a knot on both ends to avoid the same incident from happening again.
Using a Safety Pin
This method is one of the most effective around.
To do this, you start by sliding a safety pin from the end of the drawstring channel. You enter from the hole where the drawstring is stuck.
The next step requires you to feel through the material. Make sure that once you can feel the end of the drawstring. Grip the pin flat.
While in this position, hold the pin on the string end. After this being able to hold the pin, slide the string channel material over the pin. Once this is finally done, grab the end of the pin.
When you are already able to grab the end of the pin, draw the hoodie material back. Make sure that you draw it back and over the string.
Do not stop until you already have the string out on the other end of the channel.
And as always, tie a small knot on each of the drawstring’s ends. This should avoid the same thing happening again.
Using a Paper Clip
When using a paper clip, the first thing you need to do is to form a hook on one end of the clip. To do this, you can make use of nose pliers. This should make things easier for you.
Once you have a hook formed, slide the paper clip into the drawstring channel. While doing this, you need to bunch up the material at the same time.
Next, you need to slide the paper clip. Do this until you are about an inch past the end of the drawstring you are trying to pull.
Rotate the clip a few more times. Grab the drawstring.
Once you can grab it, slide the clip out of the hole. Do this slowly. But also make sure that when you are drawing the clip out, the drawstring is also attached.
Once done, tie both ends into a knot.
Using a Drinking Straw
A drinking straw may not sound like much. But you can also use this in getting the drawstring back to where it belongs.
First, slide the straw into the hole where the drawstring should be.
The straw should be able to travel from that hole. This is until you can reach the drawstring that you will be pulling out. Make sure that you slide the straw up until the end of the drawstring in question.
In this step, you have to attempt to stick the string into the straw. Once this is finally done, pull the straw out. The drawstring should go with the straw.
Once the drawstring is out, tie both ends into a knot.
Are you supposed to tie hoodie strings before washing?
Washing can tangle and do wonders to your hoodie’s drawstrings. It can pull the drawstring out as it tangles with zippers and buttons in the wash. To avoid this, one can tie a knot at the end of each string. This should help the drawstring stay in place.
We know how much of a struggle it is to find the drawstring halfway out of the hoodie. And this can happen. It can be because of accidentally pulling the string out. Or it can also be because the drawstring got tangled in the wash.
Yes, it can hold on to buttons. It can get itself tangled in zippers and other pieces of clothing.
And once you get it out of the wash, you would find the drawstring already halfway out.
Now, there are ways by which to avoid this.
The simplest of all is to tie a knot at the end of each string.
Tying a knot would ensure that the drawstring does not get pulled out of the channel. This is critical, especially during the washing process. This should keep the drawstring in place from washing until drying.
When doing this, however, one should be wary of the size of the knots.
This is because some holes may be bigger than the knots.
You need to make sure that the knot is actually bigger than the hole of the drawstring channel. This should prevent the drawstring from going through the hole.
Another way you can ensure the drawstrings do not get pulled through is to use a safety pin. Attach a safety pin at each end of the drawstring in the hoodie. Do this before putting the hoodie in the wash.
No matter how the drawstrings get twisted around, they will remain in place. They don’t get caught on zippers and other pieces of clothing.
This should be able to solve your problem.
How often do you wash hoodies?
You can wear a hoodie many times before washing it. In fact, the rule of thumb is that you can wear it about five or six times before washing. This is, of course, as long as the hoodie is not stained. This is provided that the hoodie does not accumulate enough dirt. You can still wear it five to six times before it hits the washing machine.
Now, if there comes a time when your hoodie gets minor stains, you don’t necessarily have to wash them right away. If these are smaller stains, you can do something about it to remove the stains. There is no need to put it in the washer.
Hoodies are mostly cotton.
Cotton is a fabric that is actually made of fibers. This makes it hard for you to remove the stains. This is especially true if you are not careful.
When removing stains, follow these few simple steps.
Removing Stains
When a hoodie gets its fair share of stains, make sure to spot treat the stain right away. You can do this right after the hoodie gets stained. You can also do this as soon as you realize there is a stain.
Now, once you can identify the stained parts, you need to discover what caused it. This should prevent you from getting additional stains into your hoodie.
Start by rinsing it. As much as possible, use warm water.
The next step may be a bit weird, but home remedies dictate that you should put white vinegar on the stain. This should wet the area. This should also wet the stain.
Leave it for about an hour.
Next, wash the hoodie through a cold-water wash cycle. Once done, try to check if the process got rid of the stains.
If it is still there, dab it with a bit of hydrogen peroxide. This should bubble. When this happens, it means that the chemicals you put into the stain are showing its reaction.
Leave it for about 10 to 15 minutes. Finally, rinse with warm water.
If there is one thing you should be careful about, it is hot water.
Hot water and hoodies do not mix well together. Hot water, in fact, can worsen the stain. Also, it can result in your garment shrinking.
Washing Without Pilling
Most of the hoodies that we see in the market today have anti-pilling characteristics. But even with this type of technology, one would still see pilling happening. This is especially if the hoodie had been in use for many years.
But fear not because you can actually prevent pilling from happening.
When washing your hoodie, turn it inside out.
Make sure to wash the hoodie in a delicate mode. Another option is to hand wash it.
Finally, do not ever use a dryer. When drying, lay your hoodie flat on a surface.
At times, you may be in a hurry. Should this be the case, use the lowest heat setting possible. But as much as you can, avoid using this. Letting the hoodie dry naturally is the best recourse.
Removing Pilling
Pilling happens only in older hoodies. This may not be something you would encounter with newer ones.
And so, if you have an old hoodie, you still would like to wear, this may be a challenge. But know that you can actually have the pilling removed.
There are a few simple ways to do that.
One of these ways is using a fine-toothed comb.
When doing this, lay the hoodie on the surface. Gently comb against the pilling. This should remove them.
You can also use a pair of scissors to remove them.
When using scissors, you only need to cut off the pilling. Just make sure never to go too close to the fabric of the hoodie.
Note, however, that this may take a while. You would need to exert more effort with this method. Especially when there is too much pilling, your patience is needed.
Finally, you can also use duct tape to remove pilling.
Start by dabbing the hoodie with duct tape. You should, of course, use the sticky part of the tape.
The pilling will go with the sticky part of the duct tape. This should remove the pilling from the hoodie.
And if there are a few more that remain, you only need a pair of scissors.
Carefully cut them through until you got them all gone!
Easy, right?
Related posts:
How to tie laces on a hoodie
20.10.2020
Beauty is in the details. That is why it is so important that every detail in the preparation of the image – both solemn and everyday – looks spectacular. This will allow not only to emphasize your individuality, but also to feel at 100. And if it is appropriate to decorate an elegant dress or a business suit with all kinds of decorations, then for sports-style clothes you need to choose other options. A great way is to tie the laces beautifully on a sweater with a hood. Consider both the simplest and original options for hoodies and sweatshirts.
Contents
- 5 quick and easy ways to tie laces on hoodies and sweatshirts
- Rabbit ears
- Ayan Figena bow
- Sherpa knot
- Ashley’s knot
- Turquoise turtle
- Lynch knot
- Diamond medallion
- Monkey Fist
- Monkey chain
- Straight Braid
5 quick and easy ways to tie laces on hoodies and sweatshirts
To begin with, we propose to figure out what is the difference between hoodies and sweatshirts that are so common among fans of dressing in sports. Sweatshirt – a sports jacket made of knitted fabric of a solid knit. Hoodie – the same sweatshirt, only with a large pocket in front. Both sweatshirts necessarily have a hood with a drawstring, which, if desired, can be tightened and ensure a snug fit of the fabric to the body, or simply tied nicely.
Rabbit ears
A classic of the genre and, perhaps, the most elementary way to tie fixing ropes on the hood of a sports sweater.
- Fold in two loops, one from each drawstring of a hoodie or sweatshirt.
- Then a bow is formed from them by interlacing.
The knot looks simple, but quite beautiful – the main thing is to observe the symmetry of the loops and freely hanging ends. This option is often used to fix the laces on outerwear, such as jackets or parkas. But this is a completely different story, which you can read about in the article “How to tie shoelaces on a jacket, park.”
Ayan Figena Bow
Its author is the Australian Ian Fieggen, who is rightfully called the professor of lacing. He came up with over 30 methods for how to tie your shoelaces beautifully. The most widespread was the bow of Ayan Figena.
- The algorithm of actions is quite simple.
- Two loops are formed from the laces.
- The loops are brought out through each other and tightened tightly.
It turns out an unusual and strong knot that will decorate any sports jacket – be it a hoodie or a sweatshirt.
Sherpa knot
Also known as surgery. Differs in reliable fixation and simplicity of execution.
- We begin to tie the usual knot, which is known to everyone since childhood. It is important that one end is longer than the other.
- Next, we form a loop from a short one, go around it with a long one.
- After that, we form a second loop from the long end of the tie and pass it twice through the middle of the first. This will provide a better hold.
To tie the laces on a sports jacket in this way means to be sure that the ropes will not untie. This will allow you not to experience discomfort in the cold season, when warm clothes are put on top, for example, a parka, which fits perfectly not only in business, but also in sports style. You can read more about this in the article “What to wear with a parka”.
Ashley’s knot
It is also known under the name – furrier. Knotting guru, American writer, artist and journalist Clifford Warren Ashley invented it on February 3, 1934.
To tie the laces on a hoodie, you need to perform a number of simple manipulations.
- A loop is formed from one lace of the jacket with the free end up.
- The second fixing tie completely repeats the geometry of the first. In this case, the running end is passed first under its own root section, and then over the root section of the first lace.
- Both ends are passed through the middle of the formed loops.
- Tails are tightened.
If you tie the laces on a hoodie or sweatshirt in this way, you will have to make an effort to untie them.
Turquoise turtle
An interesting name appeared due to the shop of the same name, which used exclusively this method of lacing on boots. Over time, they began to tie fixing ropes on clothes in this way: hoodies, sweatshirts and even jackets. The reason is that it looks beautiful and is easy to do.
- We form “rabbit ears”.
- We pass one loop through the middle of the second twice and tighten tightly.
Tie with a “turquoise turtle” is recommended in cases where it is important that the knot is not untied. For example, if you have a long run or an intense workout in a fitness club.
5 original ways to tie the laces beautifully on the hood of a sweatshirt
For those who are not looking for easy ways, there are several options that require more time and patience. However, the result will exceed all expectations and give the sports jacket an unusual look. As a rule, unlike the simple methods of tying the laces on a sweatshirt, the original options differ in that the laces are not intertwined. Therefore, we are not talking about fixing the hood on a hoodie, but about a decorative decoration.
Lynch knot
Also known as the hangman’s noose or scaffold knot. Despite the rather gloomy names – this method of tying a rope was used during the death penalty by hanging – the knot looks quite original and is able to surprise or even shock others.
You can tie the laces on the hood of a hoodie or sweatshirt with a Lynch knot either together or separately. Consider the option using the example of one fixing rope.
- We fold the lace of a sports sweater according to the zigzag principle. The result is two loops.
- Next, with the free end we form a transverse lacing, bending around the loops from the bottom up. How many times this can be done depends on the length of the string. The main thing is that the number of turns must be odd!
- Pass the remaining tail through the top loop and tighten tightly.
Whether to tie the laces on a sports jacket in this way is a personal matter for everyone. In any case, it is desirable to remember the history of its origin.
Diamond medallion
Also known as the Josephine pattern. Such beautiful names are quite consistent with the appearance. To tie the laces on a hoodie in this way, it is recommended that you first lay out the jacket evenly on the surface.
- Straighten the ends of the fixing ropes.
- We form a loop on one lace.
- The second is carried out under the formed loop, then over its free end and brought up under the root section.
- We pass the tail of the second lace through the core of the loop and get a beautiful pattern.
How much to tighten the ends of the laces on a sports jacket, decide for yourself. The weaker, the more voluminous the medallion is.
Monkey fist
This method of tying laces on a hoodie owes its name to sailors. They compared the knot formed in the process with a narrow vessel through which monkeys were caught.
The process is quite complicated, but it’s worth it – the result will be a rather original decoration of any sports sweater.
- We wind the end of the lace around four fingers of the hand. 3-4 turns are enough.
- With the remaining tail, we wind across the formed loops.
- We remove the resulting creation from the hand and wrap the end of the lace a couple more times.
- We wind the tail inside the braid – 3-4 times alternately in one loop, then in another.
- We give shape, gently pulling each loop.
The whole process can be seen in the video.
Interesting! Life hack for beginners – inside you can put a miniature ball, for example, made of metal. This will give the node the most correct shape.
Monkey chain
A method that will allow not only to create a beautiful decor for a sweater with a hood, but also to significantly shorten too long laces. To tie a monkey chain on a hoodie or sweatshirt, you need sleight of hand and a little patience.
- We form a loop around.
- Hold the intersection with your thumb.
- From the free edge of the tie we create a second loop and thread it inside the first.
- We transfer the thumb to the intersection of the loops.
- Next, we continue to create loops, not forgetting to thread each new one into the previous one.
- At the end, we thread the tail into the loop and insert a small stick that will prevent blooming.
The result is a chain of links, the number of which is strictly individual and depends on the length of the lace.
This way to beautifully tie fixing ropes can also be used on outerwear, for example, parks. The main thing is to choose an original jacket, which necessarily has long ties-clamps. How to do this, you can learn from the article “How to distinguish a fake and choose a quality parka. ”
Straight braid
You should immediately be prepared that the first time it is unlikely that something will work out. However, if you practice, it is quite possible to achieve perfection and beautifully tie the ropes on a hoodie or sweatshirt.
- Approximately in the middle of the free edge of the lace, we form a loop from left to right.
- Next, from the bottom up, we create the most tight turns around the root section with a free tail, while maintaining the original direction.
- At the end of the winding, we pass the free end through all the resulting loops.
- We tighten.
To make the braid look beautiful, it is recommended to tie rather tight laces on a sports jacket. Simply put, the ties should be a kind of miniature copy of the rope.
Each of the knots is interesting in its own way and worthy of decorating a hoodie or sweatshirt. Therefore, it is worth trying all the options. And there are a huge number of them, in addition to those listed above. On the Internet you can find both a text description with diagrams and a video. By experimenting, it is possible not only to choose the most suitable option for yourself, but also to spend your free time interestingly.
How to insert an elastic or drawstring into pants, a skirt, a jacket
How to fold origami Japanese wreath
DIY Christmas star easy and simple
- Posted in Minor Repairs
You can’t mend your socks, you can’t stomp in new clothes. A diligent housewife should be able to sew on a button and put a patch, and she certainly knows how to insert an elastic band into panties, pants or a skirt. Indeed, if, faced with a small problem in the form of a torn button or a small hole in your clothes, you run to the store to buy new things, then all your salary in the store will remain.
How to sew on a button can be found here. And this article talks about patches. Today we will talk about how to insert an elastic band (or lace) into pants, a skirt. The elastic waistband is very comfortable. She is easy to put on and holds up well. However, all its benefits disappear immediately, as soon as the elastic is stretched and ceases to be elastic or simply breaks. You should not refuse clothes if the whole problem is in a stretched (or torn) elastic band. Inserting a new rubber band is very simple and does not take much time.
What you need
- Elastic band,
- sewing threads,
- pin,
- sewing needle
- and scissors.
How to use
Elastic band comes in different colors and widths. Therefore, we choose the most suitable for clothes. Decide on the required length. You can wrap the elastic around the waist and pull it slightly. It should sit tight, but not push. Many reputable publications recommend the length of the elastic equal to the waist, reduced by 5-12 cm. For thin knitted fabrics, this value approaches 12 cm. For denser fabrics, up to 5 cm.
Attach a pin to one end of the elastic band.
Insert the drawstring into the hole and pull like a needle and thread. We follow the free end of the elastic band so that it does not run away.
Disconnect the pin when it comes out the other end.
We connect the ends of the elastic band with an overlap of 1-2 cm and sew with threads in the color of the elastic band.
Spread the elastic evenly over the entire length.
The technology is the same for panties, skirts and panties.
There are situations when there is no pin at hand, and the rubber band needs to be put in very urgently. Replace the pin with a regular paper clip. The clip sticks perfectly into the rubber band. Instead of a paper clip, you can use a carnation. In this case, one end of the elastic is tied to a carnation next to the hat.
If the cord comes out of your jacket or sports trousers, attach a pin to the end of the cord and pull it through like a thread with a needle.