Introduction to replacing Yeti lids
So you’ve been using your beloved Yeti tumbler for a while now, and that lid is looking a little worse for wear. Maybe it’s gotten dinged up, the rubber gasket is wearing out, or there’s a crack that’s causing annoying leaks. Whatever the reason, it might be time to replace that trusty lid with a shiny new one.
Replacing a Yeti lid is actually a breeze. With just a few tips on finding the right replacement, removing the old lid, and properly installing the new one, you can give your Yeti a makeover with minimal effort. A new lid can also improve functionality, customizing your Yeti with different drinking openings, straw options, or just a fresh look.
In this article, we’ll walk through everything you need to know about replacing lids on your Yeti cups, bottles, mugs, and more. We’ll share pro tips on finding compatible lids, troubleshooting any replacement issues, and even adding customization. So read on for the complete guide to upgrading your Yeti with a new cap!
Picking Out The Perfect New Lid
The first step is picking out a replacement Yeti lid that will properly fit your specific drinkware. Yeti offers two main types of lids: the Rambler lids for their stainless steel tumblers and bottles, and the MagSlider lids for their plastic drinkware like the Colster cans and bottles. There are also special lids for the Yeti mugs.
When choosing a replacement Rambler lid, you’ll need to match it to the exact diameter of your cup or bottle opening. For example, the 20 oz Rambler requires a different lid than the 30 oz or 36 oz sizes. Yeti’s website has a handy lid finder tool to help you match the right lid for your Rambler based on the model.
For MagSlider lids, you’ll need to find the replacement specific to the Colster product you have, like the Can Colster 12oz lid. The lids between Colster sizes are not interchangeable. Again, Yeti provides guidance on pairing lids and Colsters.
You can purchase official Yeti brand replacement lids from their website or authorized retailers like Dick’s Sporting Goods and REI. There are also plenty of third-party versions available on sites like Amazon that work just as well for a fraction of the price.
Removing The Old Lid
Once you’ve got your new replacement Yeti lid, it’s time to remove the old one. This may take a little muscle if it’s really stuck on there!
Start by firmly twisting the lid back and forth while pulling up. You can also try wedging a spoon handle or butter knife under the edge and gently prying upwards. For a tighter seal, run the base under hot water to loosen the gasket.
Try to avoid tools like pliers that could dent or damage the rim of your Yeti. Be patient and work the lid off gently. It will pop off eventually!
If the gasket remains stuck inside the lid after removal, peel or pick it out carefully to prep the area for the new lid. Give any remaining sticky residue a wash before installation.
Installing The Replacement Lid
Once the old lid is off, you’re ready to install the new one! First, inspect the new gasket to make sure it’s aligned properly within the lid and free of any defects.
You may need to run the gasket under water to lubricate and activate the adhesive. Then simply center the lid over your Yeti opening and press down firmly and evenly around the rim to secure it in place.
Twist the lid gently back and forth to help adhere the gasket tightly. You’ll know it’s sealed properly when it clicks or snaps on cleanly. There should be no leaks or gaps between the lid and rim.
Your new lid may be stiff at first until the gasket softens. Hand wash and rinse your Yeti normally after installation to smooth it out.
Maintaining Your New Lid
With proper care, your replacement Yeti lid should seal tightly for years of use. Here are some tips to keep it in top condition:
- Hand wash only with mild soap and avoid abrasive sponges.
- Check periodically for cracks in the plastic.
- Watch for wear, thinning, or damage to the gasket.
- Avoid dropping or dinging the lid on hard surfaces.
- Store lids separately from Yetis to prevent damage.
If the lid becomes loose or leaks develop, remove debris from the gasket and wash it with soap and water. If that doesn’t improve the seal, it’s time for a new replacement.
Customizing With Fun Lid Options
One bonus of replacing your Yeti lid is getting to customize your drinkware with fun new options!
Different lid styles allow you to modify the drinking access – from wide mouths, to narrow openings with splash protection, to straw ports. You can choose different colors to complement limited edition Yeti colors. Or pick a liner that fits your needs, like a coffee splash guard.
So explore all the possibilities and find the perfect replacement Yeti lid to make your drinkware your own. A fresh new cap can lend new life to your beloved Yeti.
With this breakdown on sizing, installing, troubleshooting, and customizing replacement lids, you’ll be ready to upgrade your Yeti in minutes. Just pop off that old lid, click on a new one, and enjoy your trusty tumbler with improved functionality.
Common reasons to replace a Yeti lid
That Yeti tumbler you rely on daily to keep your drinks hot or cold can take a beating. While Yeti products are durable, the lid takes the brunt of the wear and tear. Here are some of the most common reasons you may need to replace your Yeti’s lid:
- Cracks – Small fissures in the plastic lid can develop over time, especially if dropped. These cracks compromise the integrity and cause annoying leaks.
- Broken Tab – The tab on the lid that hooks onto the lip of the Yeti can snap off, making it hard to open and close the lid.
- Fading Color – After prolonged sun exposure, the lid’s color may fade significantly compared to the still-vibrant tumbler.
- Loose Fit – The gasket inside the lid stretches out, causing a loose, sloppy fit that makes the lid prone to popping off.
- Stains – Coffee, tea, and other beverages can discolor the lid over time for an unsightly appearance.
- Rust Spots – Condensation that pools under the gasket can cause rust spots to form on the stainless steel rim.
- Bad Odor – Even after washing, the gasket area can retain odors that transfer to each beverage.
- Worn Out Gasket – Constant removal stretches and wears down the gasket, reducing its ability to seal effectively.
If you’re experiencing any of these issues with a deteriorating lid, it’s definitely time to replace it. The good news is Yeti replacement lids are readily available and very simple to install yourself.
A new factory-fresh lid will restore the perfect fit and functionality you expect from the Yeti brand. It takes just minutes to pop on a new lid, but it makes a world of difference in keeping drinks hot or cold while preventing annoying leaks.
Some other reasons you may want to swap out your Yeti’s lid even if the original is still intact:
- Customization – Change lid color or style for a whole new look.
- Enhanced Features – Choose a lid with a straw opening, chug cap, or coffee splash guard.
- Hygiene – Replace an old lid with unsanitary gasket to freshen things up.
With so many affordable replacement options, there’s no reason to make do with a compromised Yeti lid when a simple new cap can revive your tumbler.
Check your Yeti’s lid for any cracks, stains, wear, looseness, or funky smells. If it shows signs of damage, it’s time to swap it out. A new lid keeps your drinks delicious and your Yeti looking great.
Where to buy replacement Yeti lids online
Once you’ve decided it’s time to replace your worn out or damaged Yeti lid, your next step is finding the perfect new lid. While you can sometimes find them in sporting goods stores, the easiest route is shopping online for a huge selection and the best deals.
Here are the top places to buy authentic and third-party replacement lids for your Yeti tumblers, bottles, mugs, and more:
Direct from Yeti
For official Yeti brand lids, shop directly on Yeti.com. They offer replacements for all their Rambler drinkware like the popular 20 oz, 30 oz, and 36 oz tumblers. You can browse lids by product line and size.
Yeti is also the exclusive source for specially designed lids like the Rambler coffee mug lid. Their factory replacement lids ensure an ideal fit and performance.
Amazon
Amazon stocks a huge array of both official Yeti and cheaper generic replacement lids in tons of colors. You can find exact lid matches for any Yeti product. Check reviews to verify fit and quality.
Prime shipping means you’ll get your new lid in just 2 days. Browse Amazon’s Yeti department or search for your specific model like “Yeti Rambler 30 oz lid.”
eBay
eBay sellers offer new and used Yeti lids at discounted prices. You can often score brand new lids for much less than retail. Again, focus on seller reviews for reliability.
eBay is also great for finding harder-to-find lids that are discontinued or sold out elsewhere. Expect great deals on older model Yeti lids.
Dick’s Sporting Goods
Major sporting goods chain Dick’s stocks a wide range of authentic replacement Yeti lids online and in stores. Lids ship free for orders over $50.
Dick’s has an advantage of physical locations, so you can potentially find lids immediately versus waiting on shipping.
With these top online sources, finding the perfect lid replacement for your Yeti is quick and easy. Just a few clicks and your new lid will be on the way!
Finding the right lid size for your Yeti cup or bottle
If you’re a Yeti fan, you know how great their tumblers and bottles are at keeping drinks hot or cold. But with so many sizes and lid options available, it can get confusing trying to find the right replacement lid that fits your specific Yeti vessel.
Whether you’ve lost or damaged your original Yeti lid and need a new one, or want to mix and match different lid styles, this guide will help you identify what size and type of Yeti lid you need.
Check the size of your Yeti cup or bottle
The most important factor in finding the right replacement lid is verifying the size of your Yeti tumbler or bottle. Yeti vessels come in a variety of sizes, from 12 oz up to 64 oz capacity. The lid has to fit the diameter of the container opening.
If you still have the container, check the size printed on the bottom. Common Yeti cup and bottle sizes include:
- 12 oz slim can insulated
- 16 oz stackable cup
- 18 oz or 20 oz stainless steel tumbler
- 26 oz stackable bottle
- 30 oz stainless steel tumbler
- 36 oz stainless steel bottle
- 64 oz stainless steel bottle
If you don’t have the original container anymore, think about the approximate capacity to narrow down the size range. For example, was it a personal cup size around 16-20 oz, or a larger 36+ oz bottle?
Pick the correct lid series for your container
Once you know the container size, next identify which lid series is compatible with that size. Yeti lids come in three main series:
- Rambler lids – For 12-30 oz Rambler cups/tumblers
- Chug lids – For 18-26 oz Rambler bottles
- MagSlider lids – For 30-64 oz Rambler bottles
Rambler lids are sized for smaller diameter tumblers and cups from 12-30oz capacity. Chug lids fit the mid-range 18-26 oz bottles. And MagSlider lids are made for the largest Rambler bottles from 30 oz up to 64 oz.
So for example, if you lost the lid for your 20 oz Yeti tumbler, you would need a Rambler series replacement lid, not a Chug or MagSlider lid that won’t fit the smaller tumbler opening.
Match the lid style and features you want
Once you’ve determined the correct lid series for your Yeti container size, the final step is picking the specific lid style and features you want.
Within each series there are different lid styles:
- Standard lids – Basic screw-on lid
- Flip/Slide lids – Allow access to contents with one hand
- Straw lids – Have an opening for a straw
- Chug lids – Large opening for easy drinking
Standard lids are the simplest with just a screw top, while Flip/Slide lids allow you to open and drink from the side with one hand. Straw lids enable use of a straw to drink from the container. And Chug lids have a wide mouth for easy drinking.
Consider how you’ll use your Yeti and what features would be most useful. For example, Chug caps allow quick access without unscrewing the lid, while straw lids let you drink with one hand. Or you may want just a basic standard lid.
You can also mix and match different lid styles for the same container size and series. A Rambler 20 oz for instance could use a standard, flip, or straw lid. This allows you to customize your Yeti with the type of lid you want.
Where to buy replacement Yeti lids
Once you know the exact lid series and style needed, it’s easy to find replacement Yeti lids for sale:
- Direct from Yeti.com
- Authorized Yeti retailers including Dick’s Sporting Goods and REI
- Independent Yeti specialty stores
- Online marketplaces like Amazon and eBay
Buying directly from Yeti or an authorized dealer ensures you’re getting an authentic product with warranty. Yeti lids purchased elsewhere could potentially be counterfeit or third party replacements, so check seller reviews closely before buying.
Prices range from $5 for simple standard lids, up to $25+ for speciality MagSlider, Chug or straw lids. Limited edition colors and prints usually cost a bit more as well.
Make sure to closely match the size, series, and style when selecting a replacement lid. With the right fit, your drink will stay cold or piping hot so you can keep enjoying your Yeti tumbler or bottle wherever you go.
If your current Yeti lid is broken, lost, or you just want a new style, following this guide will help you easily find the perfect replacement lid. With a little knowledge of the different lid sizes and types, you can customize your Yeti container with the right top.
Checking lid compatibility for different Yeti products
When it comes to keeping drinks cold, Yeti coolers and tumblers are some of the best on the market. Their double-walled vacuum insulation can keep ice frozen for days. But with different sizes and styles of Yeti cups and bottles comes the need for different lids. Knowing which lids fit which Yeti products can be confusing. Here are 15 tips to help make sense of Yeti lid replacements.
1. The most common Yeti lid types
Yeti coolers, bottles, and tumblers come with different standard lid types depending on the product. The most common are:
- Standard Screw-Top Lids – These screw onto the top of Yeti bottles and some tumblers.
- Slider Lids – Slide open and closed to seal Yeti mugs and tumblers.
- Flip-Top Lids – Flip up to open and down to close on the Rambler tumblers.
- Straw Lids – Come with a straw that flips up to allow drinking from Yeti tumblers.
2. Know your Yeti cup, bottle, or tumbler size
Yeti products come in a range of sizes including 10 oz, 12 oz, 16 oz, 18 oz, 26 oz, 30 oz, 36 oz, 64 oz, and more. The lids are sized specifically for each container size, so know the capacity of your Yeti item before looking for a replacement lid.
3. Original lids usually only fit the original product
If you have the original Yeti product, look for the exact replacement lid made for that item. For example, the 26 oz Rambler tumbler only accepts the 26 oz Rambler Flip Lid. The lids are not interchangeable between different sized Ramblers.
4. The right lid ensures a tight seal
Using the properly sized lid for your Yeti product ensures a tight seal to keep drinks cold. A lid that is too small may be loose while one too big may not even fit. Match lid size to container size for the best insulation.
5. Know which new lids are interchangeable
Some of Yeti’s newer lids and products are designed to be more interchangeable between certain items. For example, the new Rambler Lowball 10 oz cup can accept lids from the 12 oz Rambler Tumbler.
6. Check for universal lid options
In addition to original lids, Yeti also offers aftermarket universal lids. For instance, the Yeti Rambler Universal Lid fits multiple Rambler drinkware from 10 oz to 26 oz.
7. Compare dimensions if unsure
If you can’t determine lid compatibility, check the dimensions listed for the lid opening and container opening. Match lids and products with the same or very close opening diameters for the proper seal and fit.
8. Ask the Yeti experts
Yeti’s customer service department can help identify the right lid for your product if you contact them with the item name, SKU, size, and other details. They have extensive knowledge to match lids and products.
9. Check third party manufacturers
There are also some good aftermarket companies making replacement lids for Yeti items. Brands like Takeya and Rtic make lids sized for specific Yeti cups and coolers.
10. Look for silicone lid options
Silicone lids are more flexible and can stretch to fit multiple Yeti items. Search for “Yeti silicone lid” to find aftermarket options made of this material.
11. Consider a lid with a handle
Some replacement lids add a handle for easier carrying. This can be a nice upgrade over the original lid. Just ensure the handle lid is made for your specific tumbler or bottle size.
12. Add a splash-proof slider lid
Slider style lids open and close to seal in drinks while adding splash protection. Companies like Takeya make these lids sized specifically for Yeti Ramblers and tumblers.
13. Try a lid with a straw access port
Lids with a small opening for a straw allow sipping without removing the whole lid. Brands like Cashflo make straw lids for various Yeti cups and tumblers.
14. Search for a coffee mug option
Some third party lids convert Yeti Ramblers into convenient coffee mugs. These usually include slide closures and small sipping openings.
15. Read reviews before purchasing
Checking customer reviews can reveal how well a particular aftermarket lid fits a specific Yeti product. Reviews can help determine if a lid runs large, small, or true to size.
With many lid options and variations available, finding the right replacement Yeti lid takes some research. But following these tips on measuring size, understanding product compatibility, and sourcing from reputable brands allows you to select the perfect new lid for your favorite Yeti tumbler, bottle, or cooler.
Buying official vs third-party replacement lids
When your Yeti lid gets lost or damaged, you’ll need to replace it to keep enjoying your tumbler or bottle. You can buy directly from Yeti or consider third-party lids. How do you decide between official and unofficial Yeti replacement lids? Here are 15 tips on the pros and cons of each.
1. Official lids directly from Yeti
Buying a replacement lid directly from the Yeti website or a certified retailer ensures you’re getting an authentic, high-quality product designed specifically for your Yeti item.
2. Official lids fit perfectly
Since they’re made by the same manufacturer as the original product, official Yeti lids provide a perfect, seamless fit for maximum insulation capabilities.
3. Identical performance to original lid
Replacement lids from Yeti offer the exact same double-wall vacuum insulation performance as the lid that came with your product.
4. Meets Yeti’s quality standards
You can be confident official Yeti lids meet the company’s stringent durability standards and manufacturing quality controls.
5. Correct sizing for your container
Yeti makes lids in specific sizes for each tumbler, bottle and cooler, so you know the official replacement fits correctly.
6. Leakproof, spill-resistant seal
Precision engineering by Yeti results in replacement lids that seal completely leakproof, keeping drinks securely contained.
7. Can be more expensive
On the downside, direct from Yeti replacement lids often come with a higher price tag than third-party versions.
8. Limited availability of some lids
Some older or limited edition Yeti product lids may no longer be available directly from the manufacturer.
9. Consider third-party lids
Unofficial lids from other brands can also work well with Yeti products while often costing less.
10. Lower cost than official lids
Third-party replacement lids are generally less expensive than ones direct from Yeti.
11. Wider variety of styles available
Aftermarket lids come in more options like different materials, added handles or straws, innovative openings, and more.
12. Check sizing and fit
Be sure to carefully confirm sizing as third-party lids may not always precisely fit your specific Yeti item.
13. Varying levels of quality
Some third-party lids equal Yeti’s quality while others may be flimsier. Check reviews to evaluate durability.
14. May not offer perfect insulation
Improper fit could compromise the vacuum seal, reducing the lid’s ability to retain temperature as well as an official Yeti version.
15. Avoid very cheap lids
Super inexpensive no-name lids are likely low quality. Spend a few dollars more for better third party brands whenever possible.
In the end, choosing official or replacement lids comes down to your budget and how well alternative lids fit your specific tumbler or bottle. For a perfect fit and proven performance, official Yeti lids are worth the price. But quality third party options can also be a great value while offering more variety.
How to remove an old or broken Yeti lid
Over time, the lid on your Yeti tumbler, bottle, or cooler may become damaged, cracked, or simply won’t seal properly anymore. When this happens, you’ll need to replace the worn out lid. But first, how do you get the old, stuck lid off? Here are 15 tips to safely remove a seized, broken, or outdated Yeti lid.
1. Try opening as usual
First, attempt to open the Yeti lid as normal. Carefully turn, twist, slide, or flip it open using moderate pressure. This may pop it loose if only lightly stuck.
2. Run under hot water
If the lid won’t budge, run warm to hot water over the lid edge for 30-60 seconds. This can expand the lid to make it easier to open.
3. Use a damp cloth
Wrapping the lid with a warm, damp dishcloth can also help loosen a stuck lid when combined with moderate opening force.
4. Avoid total immersion in water
While running water over the lid can help, don’t totally immerse the Yeti product in water to avoid getting liquid inside and compromising insulation.
5. Grip lid firmly
Use an oven mitt, towel, or rubber jar opener gripper to hold the lid tightly and improve traction as you turn or slide it.
6. Twist and lift simultaneously
Rather than just twisting back and forth repeatedly, twist the lid while lifting up at the same time to pop it loose.
7. Tap lid on countertop
Turn the Yeti upside down and gently tap the lid on a towel on the countertop. This shock can help break the seal.
8. Avoid using blades or sharp objects
Using a knife or other blade to pry under the lid risks damaging both the lid and your Yeti product.
9. Try lubricating seal with oil
For a rubber gasket lid, rub a small amount of cooking oil around the rim to lubricate and loosen the seal.
10. Use a rubber mallet
If other methods fail, wrap the lid in a dish towel and lightly tap the edge with a rubber mallet to jar the lid free.
11. Contact Yeti support for help
For very stubborn lids that resist all removal efforts, Yeti’s customer service experts may have additional tips and tricks to get the lid off.
12. Replace lid if damaged
If the old lid is cracked, warped, or has broken parts, it’s time to replace it with a new one.
13. Ensure gasket or seal is still intact
Examine rubber gaskets once the lid is off to be sure the sealing surface is still smooth and complete.
14. Clean lid, container, and gasket
Wash the lid, tumbler/bottle, and any gasket surfaces to remove residue buildup before installing the new lid.
15. Follow directions to install new lid
Carefully follow the instructions to install your Yeti’s replacement lid correctly to maximize performance.
With the right techniques and some determination, you can get a seized or broken Yeti lid removed to refresh your product with an effective new lid. Just take care not to damage the tumbler, cooler, or gasket surface during removal.
Steps for properly installing a new replacement lid
Once you’ve removed your old, damaged Yeti lid, you’ll want to install a new replacement lid properly to get the perfect seal. Follow these 15 steps to correctly and securely attach your new Yeti lid.
1. Choose the right replacement lid
Make sure to select a replacement lid specifically engineered for your exact Yeti model. The sizing must match precisely.
2. Inspect gasket seal surface
Examine the gasket rim where the lid attaches and make sure the surface is smooth, clean, and undamaged.
3. Wash lid and tumbler thoroughly
Use warm soapy water to wash both the new lid and the Yeti tumbler, bottle, or cooler it will attach to in order to remove any residue.
4. Dry components completely
Dry the lid and Yeti container fully with a clean towel to prevent water interfering with the seal.
5. Align arrows or indicators
If present, align arrows, notches, or alignment indicators on the lid and tumbler to ensure proper positioning.
6. Insert gasket or seal in lid groove
If the lid contains a removable gasket, firmly press it into the gasket groove in the lid to secure it.
7. Position lid straight on
Place the lid evenly and straight on the tumbler or cooler opening, avoiding tilting it initially.
8. Press lid down firmly
Once the lid is properly positioned, press it straight down firmly to compress the gasket and create a tight seal.
9. Twist lid clockwise to lock
For screw-on lids, turn the lid clockwise while continuing to push down until it won’t rotate further to tighten.
10. Close security tab or latch
If present, rotate, close, or latch any security tab feature to fully lock the lid in place.
11. Perform a test shake
Gently shake the sealed Yeti product upside down and right side up to verify the lid stays securely attached.
12. Test lid seal with water
Add a small amount of water to the container and seal lid to check for any leaking to confirm full gasket seal.
13. Adjust lid if needed
If leaks occur, remove the lid, realign, and reinstall pressing even more firmly to improve the gasket seal.
14. Avoid overtightening
Overtightening can warp the lid. Tighten just until the lid no longer rotates freely.
15. Contact Yeti support if issues
If the new lid still does not seal after adjusting and reinstalling, reach out to Yeti support for additional troubleshooting help.
Carefully following the proper installation instructions ensures your new Yeti replacement lid forms a leakproof, insulating seal. With a bit of care, your Yeti will once again be ready for all your adventures while keeping drinks icy cold.
Maintaining and cleaning replacement Yeti lids
Once you’ve installed a new replacement lid on your Yeti product, proper maintenance and cleaning is required to keep it in top shape. Follow these 15 tips to take care of your new Yeti lid.
1. Hand wash regularly
Use mild dish soap and warm water to hand wash your Yeti lid after each use to prevent stain and odor buildup.
2. Rinse lid thoroughly after washing
Always rinse the lid fully with clean water after washing to remove any soap residue that could affect the flavor of drinks.
3. Dry lid completely
After washing and rinsing the lid, dry it fully with a clean towel to prevent moisture from getting trapped under the lid.
4. Check gasket periodically
If your lid has a rubber gasket seal, periodically inspect it for damage or cracking and replace if needed.
5. Keep gasket clean
Use a clean small brush or sponge to gently wash the lid gasket after each use to prevent buildup.
6. Avoid harsh cleaners
Skip abrasive brushes, scouring pads, and harsh chemicals that could scratch or damage the lid’s finish.
7. Try diluted vinegar for disinfecting
For occasional disinfecting, use a 50/50 white vinegar and water solution to soak the lid for 15 minutes then rinse fully.
8. Store lid on or off container
You can store the clean lid either attached to your Yeti item or separate. Storing it on helps avoid losing lids.
9. Ensure lid is fully dry before storing
Never put away a damp lid as moisture can cause odors or mold. Always fully dry after washing.
10. Use a lid-drying rack
Let your clean Yeti lid dry completely in a dish drying rack before putting it away to prevent moisture issues.
11. Try storing with crumpled paper inside
Ball up some paper towels and place them inside your Yeti container when storing the lid on top to absorb odors.
12. Use baking soda for odors
Sprinkle some baking soda inside your empty Yeti before sealing the lid closed to keep smells fresh.
13. Avoid harsh scrubbing
Scrub gently when washing lids to prevent scratching the finish. Use soft sponges and brushes only.
14. Check for warping
Inspect your lid occasionally for any warping that could affect the seal. Replace warped lids promptly.
15. Contact Yeti for damage issues
If your replacement Yeti lid damages easily, contact Yeti to determine if your product might be defective.
Proper care and cleaning is key to keeping your replacement Yeti lid looking and working like new. Follow these tips to enjoy many adventures with your trusty Yeti tumbler.
Extending the life of your new Yeti lid
Let’s be honest – we’ve all been there. You spend way too much money on a fancy new Yeti tumbler because you just have to have the same one your bestie has. You proudly carry it around and post pics on social media to show it off. But a few weeks later, you notice the lid already has some scratches and discoloration. Dang it! Now your shiny new toy doesn’t look so perfect anymore. But before you chunk that beat up lid and buy a replacement, hold up just a sec. With some TLC you can keep your Yeti lid looking fresh and new for much longer. Here are 15 helpful tips to extend the life of your Yeti lid so you get your money’s worth out of it.
1. Hand wash only
It may be tempting to just pop that lid in the dishwasher with the rest of your dishes to make cleanup easier. But the harsh chemicals and hot water can prematurely wear down the plastic, causing cracking and fading. Instead, gently hand wash the lid with mild dish soap and warm water. This will help maintain its integrity and appearance for longer.
2. Avoid harsh cleaners
Stick to gentle soap and water for cleaning your Yeti lid. Avoid using harsh chemicals or abrasive scrubbers. The rough texture can lead to surface scratches on the lid. And chemicals like bleach can react with the plastic material, resulting in discoloration or other damage over time. Play it safe with mild soap.
3. Don’t let it soak
While it’s often recommended to let dishes soak before washing, don’t let your Yeti lid sit in water for extended periods. Letting it soak too long, especially in hot water, can cause the plastic material to become compromised or warped. Give it a quick rinse or scrub, but don’t leave it to bathe for a long time.
4. Dry thoroughly
After washing your lid, dry it completely with a soft towel. Don’t let moisture linger. Water droplets on the surface can act as tiny magnifying glasses in the sunlight and burn spots into the plastic. Wipe it down well so no water remains.
5. Keep it covered
When not in use, keep the lid securely on your Yeti cup. This protects the inner and outer surfaces from dust, dirt, scrapes and other damage. Bonus tip: Attach the included silicone strap to your lid/cup to keep them together when not in use.
6. Store it properly
Choose a safe spot to store your lid when not attached to your Yeti. Keep it away from heat sources, direct sunlight or potential puncture hazards. Stash it in a cabinet, drawer or clove for lid protection.
7. Inspect it often
Make it a habit to inspect your lid on a regular basis. Look for any cracks, punctures, tearing or warping. This can help you catch small problems early before they turn into big damage. Early detection means you can take action and extend its life.
8. Replace gaskets annually
The gaskets on Yeti lids help create a leakproof seal. But these rubber gaskets can get worn down over time with regular use. Plan to replace your lid’s gasket once a year to keep it sealing properly. Yeti sells replacement gaskets for all mug and bottle sizes.
9. Use caution with heat
While Yeti tumblers are designed to handle hot drinks, take care not to expose the lid to extreme heat that can warp or damage the plastic. Don’t place it directly under hot water or leave it sitting atop a steaming cup. And never put it in the microwave.
10. Don’t overfill
Avoid overfilling your Yeti cup. Too much liquid can pressurize the container and cause leakage around the lid. This can lead to premature wear. Leave a little air space at the top for optimal performance.
11. Keep the seal clean
Don’t let gunk build up where the gasket seals against the rim. This can prevent it from sealing properly and cause leaks. Clean this area regularly with a cotton swab and warm, soapy water to keep the sealing surface clean.
12. Check for damage
Inspect the rubber gasket for any cuts, tears or cracks that could affect its ability to seal tightly. Look at the hinge area too. Damage here can impede the lid’s ability to open and close properly. Replace if needed.
13. Avoid drops
Dropping your Yeti can damage the lid, even if the cup is fine. The force of impact can crack, warp or scratch the lid. Carry and handle your Yeti carefully to avoid accidental drops and bumps.
14. Skip the dishwasher
We covered this already, but it bears repeating. The dishwasher’s harsh effects can degrade your lid over time. Stick with gentle hand washing to keep it looking pristine longer.
15. Use a protective case
For extra protection when out and about with your Yeti, use a protective silicone or fabric case. This shields your lid from dings, scrapes and surface damage when tossed in your bag or car. Bonus: It helps insulate your drink too!
By caring for your Yeti lid properly and fixing small issues before they grow, you can get years of use from it and protect your investment. With some simple maintenance and TLC, your lid will maintain its good looks and leakproof performance for the long haul. So you can enjoy your overpriced tumbler guilt-free. Now go flaunt that sucker on social media again!
Replacing rubber gaskets and O-rings in lids
If you’re anything like me, you rely on your Yeti tumbler to keep your favorite beverages nice and chilled – or piping hot for that morning coffee. But over time, the rubber gasket or O-ring inside the lid can wear out or get damaged, causing annoying leaks and spills. Replacing those gaskets and O-rings is usually pretty straightforward, but there are some handy tips and tricks to make the job easier.
First things first – identify the source of the leak. Take a close look at both the gasket and O-ring and check for any cracks, tears, or deformation. Give them a gentle squeeze to see if they still have some spring and flexibility. If either seal shows obvious signs of wear, it’s time for a replacement.
When ordering replacement parts, be sure to get the right size and material – Yeti offers different gasket and O-ring options depending on the tumbler model and lid size. Their website has helpful compatibility charts to get the right fit. While you’re at it, consider grabbing a few spares so you’ll have backups on hand for future repairs.
Here’s the step-by-step for replacing the gaskets and O-rings in the most common Yeti lids:
D-Ring Cap
This is Yeti’s standard screw top lid found on most of their 20oz and 30oz tumblers. Replacing the parts is quick and easy:
- Unscrew the lid and remove the drink opening cover.
- Use your fingernail or a small flathead screwdriver to pry out the old rubber O-ring. Make sure to remove any remaining debris or residue.
- Take your new O-ring and press it into the groove on the underside of the top lid.
- Align the drink opening back into place over the O-ring and firmly press the lid back on so the O-ring seats properly.
MagSlider Lid
The MagSlider is the magnet closure lid on Yeti’s 26oz Rambler bottles. Just a few steps to swap out the gasket:
- Pop the drink hole plug out of the lid.
- Use a small pick to get underneath the gasket and peel it out.
- Clean any remaining adhesive residue from the lid so the new gasket adheres properly.
- Remove the backing paper from the new gasket.
- Carefully press the gasket into place, making sure it lays flat and forms a tight seal all the way around.
- Replace the plug.
Chug Cap
Yeti’s Chug Cap lids have a large opening with a hinged cover. Here’s how to replace the gasket:
- Open the hinged cover all the way.
- Grab the edge of the gasket and slowly peel it off the lid.
- Use a paper towel to remove any dirt or oils from the lid surface.
- Peel the backing off the new gasket.
- Starting at one side, carefully press the gasket onto the lid, working your way around the opening to avoid bubbles and wrinkles.
HotShot Cap
Designed for hot drinks, the HotShot lid has a removable plug stopper. Just follow these simple steps for new gaskets:
- Pull the plug completely out of the lid.
- With your fingers, grasp the gasket and rotate it counterclockwise to unscrew it off the threaded posts.
- Screw the new gasket piece back on clockwise so it is flush with the top of the posts.
- Replace the plug.
And that’s really all there is to it – with just a few minutes and basic tools, you can easily breathe new life into worn out Yeti lids. Going forward, be sure to hand wash your lids after each use and avoid putting them in the dishwasher, as excessive heat can accelerate degradation of the rubber seals. With proper care and occasional gasket replacement, your Yeti tumblers and caps can last for years of dependable use.
Fixing leaks in a damaged or worn Yeti lid
As a Yeti tumbler owner, you know that a properly sealing lid is crucial for keeping your drinks at the perfect temperature. But over time, normal wear and tear can cause lids to develop annoying leaks. Before replacing the whole lid, try fixing those pesky leaks first with some easy troubleshooting tips.
Start by examining the lid closely to locate the source of the leak. Are drops coming from the edge of the gasket? Is liquid seeping through cracks or holes in the plastic? Identify the problem area so you can tackle it directly.
For leaks around the gasket, the seal may be compromised. Remove the gasket and check for tears, cracks, or deformation. Stretching out old and dry gaskets can sometimes extend their life. Or apply a thin layer of food-grade silicone grease on the gasket to rejuvenate the seal. If the gasket is too far gone, swap in a new one.
For cracks and holes in the plastic lid components, apply a sealant like clear nail polish or super glue to fill in the problem spots. This works best for minor cracks. Cover larger holes or splits with patches of waterproof tape on the inside of the lid. Duct tape works in a pinch, but look for beverage-safe repair tapes for the most reliable fix.
In some cases, the plastic lid may become warped or bent over time, preventing a tight seal against the tumbler rim. Gently bend or flex the lid back into its original shape so it sits flush against the cup again. Place the lid on a flat surface and weigh it down for awhile to retrain the shape.
Loose or missing screws can also contribute to leaks around certain style Yeti lids. Tighten any loose screws with a screwdriver and reapply threadlocker gel to help secure them in place. For broken or lost screws, Yeti sells replacement screw sets for most models. Just be sure to get the right size and thread style.
If the drinking opening of the lid has become widened or deformed, causing splashing and spilling, try inserting an additional gasket to tighten the fit. Trim a compatible gasket to fit snugly in the opening and test the seal. Buying a new drink hole cover that fits securely may also do the trick.
For hard-to-solve leaks in metal Yeti lids, check for dents, punctures, or thinning areas in the metal that could be points of failure. While metal lids can’t easily be patched like plastic, you can try reinforcing vulnerable spots from the inside with waterproof tape. But replacement may be necessary if damage is extreme.
While wrestling with leaks and damage, be sure to clean the lid thoroughly to remove grime or oils that impede sealing. Dish soap, hot water, and occasional deep cleaning with vinegar can reveal hidden leak points gunked up by residue.
If all attempts to remedy a leaky, worn-out lid fail, then replacement is the fix. But with the handy troubleshooting tips above, you can likely get more life out of mildly damaged lids. And be sure to store lids properly when not in use – keeping them in place on the tumbler or cupped securely in your hand saves them from impact damage that can lead to leaks.
With a little TLC and clever MacGyver-ing, you can save cash on replacements and reduce waste by reviving worn Yeti lids. But when damage is beyond repair, splurging on a shiny new lid maintains the performance you expect from the Yeti name. Just take care of it properly so it lasts you for many adventures.
What leak fixes have worked for you? Share your lid repair tips and tricks to help out your fellow Yeti fans!
Troubleshooting tips for a poor-fitting replacement lid
Just got a new replacement lid for your Yeti tumbler but it’s not quite sealing right? A loose or ill-fitting lid defeats the purpose of keeping drinks hot or cold. Before giving up, try these troubleshooting tips to improve the fit and function of a replacement Yeti lid.
Start by double checking you’ve got the right lid model and size. Even slight variations between tumbler generations or lid types can cause fit issues. Refer to Yeti’s lid compatibility charts or customer service if unsure.
Carefully inspect the new lid for any manufacturing defects. Look for uneven edges, warping, or imperfections around the drinking opening and gasket areas that could impede sealing. Reach out to Yeti if quality issues are suspected – you may have gotten a lemon.
Give the gasket a good stretch before installing to maximize its flexibility and recovery. A brand new gasket may need some mechanical working-in for the best seal. You can also rub food-safe silicone grease into the gasket to aid performance.
When snapping or screwing on the lid, make sure to rotate it into the fully seated and locked position. An incorrectly aligned lid can easily leak. For screw tops, secure all screws evenly and firmly without overtightening.
Check for debris, oils, or grime buildup on the lid and tumbler rim that could create gaps in the seal. A thorough cleaning of mating surfaces helps maximize contact.
Inspect the tumbler rim for dents or irregularities that prevent the lid from sitting flush. Minor dings can sometimes be gently hammered out. But major deformations may call for cup replacement.
Try an extra gasket in the drink opening if it feels loose. A second trimmed gasket adds thickness to improve the fit. Or swap in a new drink hole cover designed for a tight friction fit.
Add a layer of waterproof tape on the inside of the lid over any gaps visible between the lid and tumbler. The tape acts as an extra sealant barrier.
For metal Yeti lids with looseness at the pivot or hinge, place a small piece of tape or gasket material between the moving parts to eliminate play and improve leverage.
In cold conditions, increased lid rigidity from temperature can exacerbate fit issues. Try warming lids prior to installation or use to increase pliability.
If all troubleshooting fails to resolve chronic leaks and looseness, the replacement lid may unfortunately need to be exchanged. Document the issues for Yeti customer service to request a replacement under warranty if applicable.
While shopping for replacement lids, look for exact matches to your tumbler’s make and model whenever possible. Cross-referencing dimensions against Yeti’s spec charts can help identify the most compatible options.
Be patient breaking in new gaskets and moving parts – you may need to experiment with tightening levels and gasket positioning before optimal sealing is achieved.
Maintain your tumblers and lids through regular hand washing and inspection for damage to get the longest life from Yeti gear. And don’t forget the value of backups – having spare lids and gaskets on hand makes it easy to troubleshoot issues.Getting the perfect liquid-tight seal on a new replacement lid just takes a little finesse. With some thoughtful adjustments and fine-tuning, you can dial in that snug, spill-proof fit. Share your own replacement lid tips below to give fellow Yeti owners a hand!
Customizing your Yeti with different lid styles and colors
One of the best things about Yeti drinkware is how customizable it is. With a huge variety of tumblers, bottles, and mugs, plus tons of lid options and accessories, you can really make your Yeti uniquely yours.
Lids are one of the easiest ways to change up the look and functionality of your Yeti. Here are some creative ways to customize with different lid options:
Mix and Match Colors
Choose lids in colors that complement or contrast your Yeti’s base color. For example, pair a seafoam Rambler with a coral lid for summery vibes. Or create an edgy black-on-black look with a solid black Stronghold lid. Having a stash of different colored lids on hand makes it easy to switch up styles.
Show Your Team Pride
Yeti offers limited edition lids decked out in team colors and logos for many popular sports franchises. Rep your home team with licensed lid designs – ideal for tailgating! Themed lids are made in limited batches so snag your squad’s gear before it sells out.
Make a Monogram Statement
Personalize with custom monogrammed or engraved lids featuring your initials. Or get creative with custom graphics and text that reflect your hobbies, interests, or business logo. Yeti’s customization shop lets you design one-of-a-kind lids to show off your personality.
Glow in the Dark Lids
Yeti’s Glow Dome lids and accessories have photoluminescent coatings that absorb light during the day and glow at night. Choose glow-in-the-dark lids for easy finding at campouts, concerts, or late night adventures.
MagSlider in New Colors
The popular MagSlider lids magnetic closure comes in the full Yeti color spectrum. Search for special edition hues like Seafoam Green, Coral, or Aquifer Blue to customize your Rambler. The magnet infused slider glides smoothly for a satisfying fidget factor.
LE Metal Handles
Fancy up your Yeti with Limited Edition drinkware featuring colorful powder-coated steel handles and metal lids. Handsome Harvest Red and bold Chartreuse handles pair nicely with coordinating or contrasting solid metal lids.
Simple Straw Lids
For an understated look, check out Yeti’s low-profile Rambler Straw Lids. The slim lids are minimalist magic for straw sipping, available in solid neutrals like black, white, and stainless steel.
Duracoat Color Shift
Special edition Duracoat Drinkware shifts between two stunning colors. Pair your color-shifting Rambler with a contrasting opaque lid for mesmerizing mismatched style.
graphicSTRONG Lids
Make a bold statement by topping your Rambler with eye-catching graphicSTRONG lids sporting abstract prints, nautical themes, camo patterns, and more. The durable lids add stylistic durability.
Mixing and matching lids, handles, and accessories create endless custom combos perfect for any personality or occasion. Coordinate your lids and drinkware colors for a polished put-together aesthetic. Or for an eclectic vibe, mismatch with wild abandon!
Keep an eye out for Yeti’s seasonal lid drops and limited edition caps built for everything from Oktoberfest and Pride Month to Disney collabs and exclusive events. Part of the fun is curating your collection over time as new designs are released.
And if you can’t find a lid style you love, Yeti’s customization shop lets you dream up your own. Add a personal touch with initials, numbers, graphics or photos that reflect your passion. With the right lid, your Yeti will be as unique as you are!
How do you like to customize your Yeti? Share your favorite lid looks and tips for making it your own in the comments!
Reviews of the best replacement lids for Yeti cups and bottles
Let’s face it – after years of regular use, Even the strongest Yeti lids eventually need replacing. When the time comes to swap out your worn or damaged lid, you want to make sure you get a replacement that lives up to the Yeti name. Here are reviews of some top-rated replacement lid options for your Yeti drinkware.
YETI Rambler D-Ring Cap
Yeti’s own D-Ring Cap is designed to directly replace the standard screw-on lids included with Ramblers and other Yeti cups. Made from durable BPA-free plastic, the leakproof cap fits 20 oz and 30 oz tumblers and includes the convenient D-ring for easy carrying. The snug twist-on gasket provides an insulated seal to lock in temperatures. True to Yeti’s reputation for quality, this cap is a great OEM lid replacement.
YETI Rambler Straw Lid
Ideal for the 20 oz Rambler, YETI’s slim-profile Straw Lid lets you sip easily while keeping spills at bay. The dual-slide mechanism protects the straw when not in use. The simple, lightweight plastic lid comes in a variety of colors to customize your cup’s look. Fits the Rambler like a glove for leak-free performance.
YETI Rambler Chug Cap
With its large opening and hinged cover, the Chug Cap facilitates easy gulping from 30 oz Rambler tumblers. Made from durable BPA-free plastic, the gasket twists on tightly while the rotating closure flips back fully out of the way between drinks. Great for quenching thirst on the go without worrying about spills.
Takeya Actives Lid
This sturdy screw-on plastic lid fits most Yeti tumblers, including the 36 oz Rambler. The flexible rubber gasket creates a tight seal, and the dual silicone sip spout is perfect for chugging water on bike rides or intense workouts. BPA-free and top rack dishwasher safe for convenience.
DrinkTanks Growler Lid
Compatible with Yeti’s stainless steel Growlers, this plastic screw cap replacement lid features a handy push-button pressure release. The gasket seals tight while the pressure valve lets you vent the Growler to control foaming when pouring. Made from durable BPA-free plastic.
SIPPR Lids
SIPPR offers plastic screw lids in a range of styles that are designed to fit 20 oz and 30 oz Ramblers. Choose from sip lids, chug lids, straw lids, or splash-proof lids with unique one-touch open/close functionality. The tight-sealing gaskets keep drinks secured.
MagSlider Lids
Replacement magnetic MagSlider lids are available from multiple brands to fit Yeti’s 26 oz Ramblers. These durable BPA-free lids mimic Yeti’s patented magnetic closure slider for effortlessly opening and closing with one hand. Great quality at lower cost than Yeti-branded.
Takeya Spout Lid
Takeya’s plastic screw-on spout lid is another great replacement for 20 oz and 30 oz Yeti tumblers. The leakproof gasket seals tight while the hinged silicone spout flips up for convenient sipping then snaps closed to lock in temperature. Dishwasher safe and durable.
When replacing worn Yeti lids, be sure to choose options specifically designed as replacements for the Rambler or Growler model you have. Looking for lids made to fit, versus generic lids, ensures the best compatibility and performance. And buy from reputable brands like Yeti itself or specialists like Takeya and SIPPR for proven quality.
With so many replacement lid options available today in various styles, colors, and materials, you can easily find the perfect new topper for your beloved Yeti. Keep your drinks delicious and secure for years to come.